River Falls, WI · East Twin Cities Metro Mon–Fri 8a–5p · Sat by appt Owner-operated · Veteran-friendly (715) 307-8302

Patios & Porches · Burnsville, MN · Est. 2003

Patios & Porches in Burnsville, Minnesota.

Burnsville is a large Dakota County suburb on the south bank of the Minnesota River, where I-35 splits into 35W and 35E. It sits directly west of Apple Valley and Eagan, both of which we already work in. We install polyurea + polyaspartic floor coatings for Burnsville homeowners: diamond-ground prep, custom flake colors, 1–2 day install, written 15-year warranty. Burnsville grew fastest in the 1960s and 1970s, so ramblers and split-levels from those decades dominate, with 1980s-1990s development filling in around Crystal Lake and Alimagnet and newer infill around the Heart of the City.

Text Dave · (715) 307-8302 See Pricing

Patios & Porches in Burnsville

What an install looks like in Burnsville.

Burnsville is a 1960s and 1970s suburb and its garages read that way: two-car attached garages on split-level and rambler floor plans, slabs now fifty to sixty years old. That is the age where a slab has usually cracked at least once from settlement, has some edge spalling where the door meets the weather, and may carry a coat of gray porch paint somebody rolled on in the 1990s. All three are prep, not problems. The 1980s and 1990s development around Crystal Lake and Alimagnet has larger three-car garages on slabs that grind clean. Homes near Crystal Lake, Alimagnet and the Minnesota River bottoms sit nearer the water table than the rest of the city, and lower-level floors there are worth testing before they are coated.

Patios & Porches specifically in Burnsville

Burnsville patios are typically 200 to 500 square feet, poured with the original 1960s-1970s house or added in a 1990s remodel, and both eras have usually moved a little by now. Polyurea with a UV-stable polyaspartic topcoat handles the freeze-thaw and full sun; anti-slip aggregate is standard on shaded and poolside slabs.

Neighborhoods we work in

  • Heart of the City
  • Crystal Lake
  • Alimagnet
  • Sunset Pond
  • Buck Hill area
  • Nicollet Commons
20+ Years installing Exterior coatings since 2003
1DAY Typical install Walk in 24h
LifeTIME UV warranty Won't yellow, ever
5.0★ Google rating From real homeowners

Why we don't install epoxy in Burnsville

Why acrylic sealers and epoxy fail outside, and what we install instead.

Most "concrete patio sealer" products at the box store are clear acrylics. They wear off in 12-24 months and offer minimal protection in the meantime. Epoxy is worse: yellows in sunlight within a year, then cracks the first winter. Both products fail on the basic problem: Wisconsin's freeze-thaw cycles demand flexibility and direct UV exposure demands UV-stable chemistry. Polyaspartic delivers both.

Acrylic Sealer / Box-Store Epoxy What you'll find at the home center
  • Acrylic sealers wear off in 12-24 months. Foot traffic, freeze-thaw, and UV exposure break down acrylic surface coatings fast. You're back at the home center every spring re-applying.
  • Epoxy yellows within a summer. Direct sunlight on epoxy turns it amber within months. By the second summer the floor looks chalked and aged.
  • Both crack across freeze-thaw. Wisconsin slabs expand and contract violently through winter. Rigid coatings fracture along the joints, then water gets under them, then the coating peels.
  • No real slip resistance. Smooth acrylic and epoxy get dangerously slick when wet. People fall on coated patios in rain, especially on stairs and stoops.
  • Salt and ice melt eat the bond. Calcium chloride and rock salt are aggressive on cheap coatings. The bond fails at the slab interface and the coating lifts.
Polyaspartic Exterior System What we install
  • Lasts 15+ years outside. Polyaspartic is the same chemistry used on industrial bridges and parking decks. It's engineered for outdoor permanence, not seasonal touch-up.
  • UV-stable to the molecule. Polyaspartic doesn't yellow, ever. The UV-resistance isn't a top-coat additive; it's the resin itself. Lifetime no-yellow warranty.
  • Flexible. Moves with freeze-thaw. Polyaspartic is approximately 100% more flexible than epoxy. Wisconsin slabs move; the coating moves with them.
  • Anti-slip aggregate standard. Every exterior install includes a slip-resistant aggregate broadcast in the topcoat. Texture level is dialed to the application: aggressive for stairs, smoother for covered patios where bare-foot comfort matters.
  • Salt + ice melt resistant. Polyaspartic handles the chemicals Wisconsin winters throw at it. We've installed exterior coatings since 2003; the warranty exists because the failure mode genuinely doesn't happen.

If you've been pricing "concrete patio sealers" or "patio epoxy," polyaspartic is the upgrade those terms should resolve to. Higher upfront cost than acrylic ($8-10 / sq ft vs $0.50-1.00 / sq ft for sealer), dramatically longer lifespan, and you're not back at the home center every spring.

Burnsville Pricing

Patios & Porches cost in Burnsville, MN: $7–9 per sq ft.

Pricing is upfront. Every number includes diamond-ground prep, polyaspartic system, anti-slip aggregate, your color choice, and the lifetime no-yellow warranty. Exterior installs price slightly higher than interior because polyaspartic resin costs more than polyurea + the prep work has to handle weather damage on the slab.

Small / Covered

150 sq ft

small covered patio or porch

From $1,200 to $1,500
  • Polyaspartic decorative flake
  • Anti-slip aggregate
  • Spalling repair if needed
  • Done in 1 day
Get my number
Most Common

250 sq ft

typical patio

From $2,000 to $2,500
  • Polyaspartic decorative flake
  • Anti-slip aggregate
  • Crack & joint repair
  • Done in 1 day
Get my number
Large / Open-Air

400+ sq ft

large patio or wraparound

From $3,200 to $4,400
  • Quartz system for direct weather
  • Maximum slip resistance
  • Phased install possible
  • Done in 1-2 days
Get my number

Stoops, steps, and walkways often combine with a patio job for bundled pricing; equipment is already on-site, so adding ~50-100 sq ft of stairs or path runs $400-800 instead of standalone pricing. Send four photos and Dave will text back a real number same-day.

The 6-step install

How we install your floor in Burnsville.

Same checklist on every floor. The reason our coatings still look new at year ten when the cheap stuff peeled in year two.

  1. 01

    Diamond grinding

    Industrial diamond-tooled grinders open the concrete pores and remove old sealers, paint, and weather-damaged surface layer. Concrete that's been exposed to weather for years has a weakened top; grinding removes it down to sound substrate.
  2. 02

    Crack repair + spalling patch

    Cracks get filled with flexible polyurea joint filler. Spalled areas (where the surface has flaked off in chunks) get rebuilt with polymer-modified concrete repair compound. Soft or unsound areas are addressed before any coating goes down.
  3. 03

    Polyaspartic basecoat

    Full polyaspartic basecoat, not polyurea-base. Polyaspartic is UV-stable from the resin up. There's no risk of substrate yellowing showing through the topcoat over time.
  4. 04

    Anti-slip aggregate broadcast

    Kiln-dried silica sand or decorative flake is broadcast into the wet basecoat. Density and aggressiveness dialed to the application: heavier for stairs, lighter for covered patios where bare-foot comfort matters.
  5. 05

    Polyaspartic UV topcoat

    Final UV-stable polyaspartic topcoat seals the system. This is the layer that delivers the lifetime no-yellow warranty + handles direct sunlight, rain, snow, and salt without degradation.
  6. 06

    Written 15-year + lifetime UV warranty

    15-year written warranty against chip, crack, and peel under normal exterior use. Lifetime warranty against UV fading on the topcoat. The exterior warranty document is handed to you at install completion.

Burnsville questions

Common questions for Burnsville homeowners.

My Burnsville garage floor was painted years ago. Can you coat over it?
We do not coat over it, we take it off. Paint is the layer a new coating would be stuck to, and it is not stuck to much. Diamond grinding removes it and opens the concrete so the polyurea bonds to the slab itself. Old paint is common on Burnsville's 1960s and 1970s garages and it adds prep time, not difficulty.
Do you cover Burnsville, or is it too far?
We cover it. Burnsville sits directly west of Apple Valley and Eagan, both of which are already on our list, and it is about an hour from River Falls.
Is a 1970s slab too old to coat?
No. Fifty-year-old concrete is generally sound concrete, it just carries more history: settlement cracks, spalled edges, prior paint, oil. The grind removes the history and we repair what it exposes. What matters is whether the slab is structurally whole, and most Burnsville slabs are.
Is polyaspartic better than acrylic sealer for a concrete patio?
Yes, by 10-15× the lifespan. Acrylic sealers wear off in 12-24 months and offer minimal protection. Polyaspartic lasts 15+ years, doesn't yellow, doesn't peel, doesn't need re-application. The math: 5 acrylic re-seals over 15 years (DIY ~$200 each + labor) vs. one polyaspartic install ($2,000-2,500 for a typical 250 sq ft patio) that's done. The professional install is competitive on lifecycle cost and dramatically better-looking the entire time.
How much does a concrete patio coating cost in Wisconsin?
Polyaspartic patio coatings in River Falls, WI run $8-10 per square foot fully installed. A typical 250 sq ft patio is $2,000-2,500 all-in. Larger patios (400+ sq ft) come in at $3,200-4,400. Bundling stoops or walkways with a patio job runs ~$400-800 less than standalone because the equipment is already on-site.
Will the patio coating crack through Wisconsin winters?
Polyaspartic is engineered for slab movement and freeze-thaw. The basecoat is roughly 100% more flexible than epoxy and moves with the concrete through temperature swings. We've installed exterior coatings across western Wisconsin and the east Twin Cities since 2003; the cracking failure mode genuinely doesn't happen on a properly prepped polyaspartic install.
Will it yellow in the sun?
No. Polyaspartic is UV-stable to the molecular level; the chemistry doesn't yellow, ever. We back this with a separate lifetime warranty against UV fading. Epoxy yellows within a summer; polyaspartic does not.
Is the patio surface slip-resistant when wet?
Yes. Every exterior install includes anti-slip aggregate broadcast into the topcoat. Texture level is calibrated to the use case: aggressive for stairs and stoops (where wet feet must not slip), smoother for covered patios where bare-foot comfort matters. We discuss the texture preference at the on-site quote.
When is the best time to coat a patio in Wisconsin?
Spring (April-June) and fall (September-October). The slab needs to be dry and the air temperature between roughly 50°F and 85°F for proper cure. Summer humidity slows it; winter is too cold. Exterior season is short in Wisconsin so book 4-6 weeks ahead during peak months.
Can you coat over an old, peeling concrete sealer?
Yes. Diamond grinding removes most old sealers, paints, and previous coatings cleanly. Anything that doesn't come off with grinding gets addressed before the new system goes down. By the time the polyaspartic basecoat is rolled on, the slab is clean substrate.
What about spalled or chipped concrete, can you still coat it?
In most cases, yes. Spalled areas get rebuilt with polymer-modified concrete repair compound during prep, then the coating goes over a smooth surface. The exception: slabs that are structurally compromised (significant frost heave, deep spalling, foundation issues) should be replaced, not coated. Dave will say if your slab needs replacement instead of restoration.
What's covered under the warranty for an exterior coating?
15-year written warranty against chip, crack, and peel under normal exterior use. Lifetime warranty against UV fading. Exclusions: damage from abuse (vehicle parking, dropped weights, etc.), neglect, or improper chemical exposure. The warranty document is real; handed to you at install completion.
Can you coat a wraparound porch or wood-and-concrete combo?
We coat the concrete portions only. If your porch is mixed wood deck + concrete, we coat the concrete and you handle the wood with a deck stain or coating separately. We can quote both portions at the on-site visit and recommend a wood finish that complements the concrete coating color.

More in Burnsville

All the services we offer in Burnsville, MN.

Whatever the slab (garage, basement, patio, mudroom, commercial) gets the same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty. Bundle pricing if you book multiple rooms in one visit.

Patios & Porches elsewhere

Patios & Porches in nearby cities.

Same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty across our entire service area. If you're outside {city}, here's where else we install.

← See Patios & Porches details and full service area

Get a quote

Ready for a patios & porches install in Burnsville?

Send four photos of your slab and we'll text back a real Burnsville number same-day. No salesperson, no quote-bot, no follow-up calls.

(715) 307-8302 Text Dave · Fastest reply
  • Free on-site measurement
  • Written 15-year warranty
FREE QUOTE

Tell us about your slab.

By submitting you agree to be contacted about your project. We don't sell your info, ever.

Text Dave (fastest) Call