River Falls, WI · East Twin Cities Metro Mon–Fri 8a–5p · Sat by appt Owner-operated · Veteran-friendly (715) 307-8302

Commercial Floor Coatings · Burnsville, MN · Est. 2003

Commercial Floor Coatings in Burnsville, Minnesota.

Burnsville is a large Dakota County suburb on the south bank of the Minnesota River, where I-35 splits into 35W and 35E. It sits directly west of Apple Valley and Eagan, both of which we already work in. We install polyurea + polyaspartic floor coatings for Burnsville homeowners: diamond-ground prep, custom flake colors, 1–2 day install, written 15-year warranty. Burnsville grew fastest in the 1960s and 1970s, so ramblers and split-levels from those decades dominate, with 1980s-1990s development filling in around Crystal Lake and Alimagnet and newer infill around the Heart of the City.

Text Dave · (715) 307-8302 See Pricing

Commercial Floor Coatings in Burnsville

What an install looks like in Burnsville.

Burnsville is a 1960s and 1970s suburb and its garages read that way: two-car attached garages on split-level and rambler floor plans, slabs now fifty to sixty years old. That is the age where a slab has usually cracked at least once from settlement, has some edge spalling where the door meets the weather, and may carry a coat of gray porch paint somebody rolled on in the 1990s. All three are prep, not problems. The 1980s and 1990s development around Crystal Lake and Alimagnet has larger three-car garages on slabs that grind clean. Homes near Crystal Lake, Alimagnet and the Minnesota River bottoms sit nearer the water table than the rest of the city, and lower-level floors there are worth testing before they are coated.

Commercial Floor Coatings specifically in Burnsville

Burnsville commercial work runs along the County Road 42 and Highway 13 corridors, the Burnsville Center retail area, and the light industrial ground on the north side toward the river. Auto bays get chemical-resistant primer under the polyurea; restaurant kitchens get OSHA-compliant anti-slip aggregate.

Neighborhoods we work in

  • Heart of the City
  • Crystal Lake
  • Alimagnet
  • Sunset Pond
  • Buck Hill area
  • Nicollet Commons
20+ Years installing Commercial coatings since 2003
24-48HRS Return to service Off-hours + weekend installs
$2M Liability coverage Certificates available
15YR Written warranty Same as residential

Why we don't install epoxy in Burnsville

Why polyurea makes more sense than epoxy in a commercial space.

Commercial floors fail in different ways than residential. Forklift point-loads, hot tire pickup from work vehicles, chemical exposure from oils and degreasers, and the financial cost of a closed bay. Standard epoxy can't handle any of those reliably. Polyurea is what industrial spaces have been moving to for the last decade, and what we install exclusively.

Standard Commercial Epoxy What most commercial installers still apply
  • Chips under forklift point-loads. A loaded forklift puts thousands of pounds on a small wheel contact patch. Epoxy fractures along the load lines.
  • Yellows under fluorescent + sun. Showroom floors photograph terribly after the first year. Customer impression matters.
  • Hot tire pickup on shop floors. Vehicles pulling into service bays hot in summer lift the coating where the tires sit.
  • 3-7 day cure = lost shifts. Standard epoxy is solvent-borne and slow. A retail floor closed for a week is real revenue loss.
  • VCT under it ages out. Commercial spaces still using vinyl composition tile waste hours every quarter on stripping + waxing. The math doesn't work past year three.
Polyurea + Polyaspartic Industrial What we install instead
  • Forklift-rated abrasion + impact. Polyurea's tensile strength handles point-loads epoxy can't. Standard rating for warehouses and manufacturing floors.
  • UV-stable for life. Polyaspartic topcoat does not yellow under fluorescent, sodium-vapor, or sunlight. Showroom floors stay showroom-grade.
  • Heat + chemical resistant. No hot-tire pickup, no peeling around oil drips, withstands degreasers and sanitizers used in daily wash-down.
  • 24-48 hour return to service. Off-hours + weekend installs are standard. Most commercial floors run prep + basecoat + topcoat over a single Saturday-Sunday and the team walks in Monday to a sealed floor.
  • VCT replacement that's permanent. Sweep and mop instead of strip and wax. Eliminates the recurring labor cost of vinyl tile maintenance, often paying back the install cost within 18-24 months on labor savings alone.

Bottom line: polyurea costs the same or slightly more than a contractor-grade commercial epoxy install per square foot, lasts 3-5× as long, requires no maintenance, and doesn't close your operation for a week to install. Every commercial customer we've installed for since the polyurea switch (2010) is still on the original floor.

Burnsville Pricing

Commercial Floor Coatings cost in Burnsville, MN: $7–9 per sq ft.

Commercial pricing varies more than residential because mobilization and crew time amortize across larger jobs. Below are typical ranges by project size + use case. Every commercial install includes diamond-ground prep, polyurea + polyaspartic system, COI on request, and the 15-year warranty. Larger jobs get phased install scheduling and milestone reporting.

Smaller Commercial

1,500 sq ft

retail showroom or service bay

From $10,500 to $13,500
  • Polyurea flake or solid color
  • Off-hours install scheduling
  • COI provided on request
  • Done in 1-2 days
Get my number
Most Common

5,000 sq ft

warehouse or auto shop

From $30,000 to $40,000
  • Polyurea solid color industrial
  • Phased install (keep operating)
  • COI + written milestone schedule
  • Done in 2-3 days
Get my number
Large Industrial

10,000+ sq ft

warehouse, manufacturing

From $50,000 to $70,000
  • Bid by scope (per sq ft drops)
  • Phased install + traffic lanes
  • Full project documentation
  • Multi-day or weekend window
Get my number

Food-service and USDA-rated installs (integral cove base, anti-slip aggregate) run $8-11 / sq ft regardless of size. Send photos + square footage and Dave will work up a written quote with line-item scope, typically within 48 hours.

The 6-step install

How we install your floor in Burnsville.

Same checklist on every floor. The reason our coatings still look new at year ten when the cheap stuff peeled in year two.

  1. 01

    Site walkthrough + scope

    For commercial projects, we start with an on-site walkthrough to scope conditions: existing coating type, slab condition, equipment that needs to stay in place, traffic patterns, and operational constraints (when can we install, what areas need to stay accessible). Written scope and milestone schedule out to you within 48 hours.
  2. 02

    Diamond grinding

    Industrial diamond-tooled grinders, larger than residential equipment, with HEPA-vacuum dust collection so we can prep occupied buildings without making the rest of the space unusable. Removes existing coatings, sealers, oil contamination, and the weak top layer of concrete.
  3. 03

    Crack repair + slab prep

    Cracks filled with flexible polyurea joint filler. Spalled areas patched with polymer-modified compound. Saw-cuts and control joints either filled flush or maintained as visible (depends on the use case).
  4. 04

    Polyurea basecoat (forklift-rated)

    Industrial-grade polyurea basecoat at higher mil thickness than residential installs. This is the structural layer that handles point-loads, equipment traffic, and impact resistance.
  5. 05

    Flake or aggregate broadcast

    Decorative flake (showroom-grade), solid color (industrial), or anti-slip aggregate (food-service / wet environments). Density and aggressiveness calibrated to the application and traffic load.
  6. 06

    Polyaspartic UV topcoat + warranty

    UV-stable polyaspartic topcoat seals the system. 15-year written warranty against chip, crack, peel under commercial use; lifetime UV-fade warranty on topcoat. Final walkthrough with operations team before we leave.

Burnsville questions

Common questions for Burnsville homeowners.

My Burnsville garage floor was painted years ago. Can you coat over it?
We do not coat over it, we take it off. Paint is the layer a new coating would be stuck to, and it is not stuck to much. Diamond grinding removes it and opens the concrete so the polyurea bonds to the slab itself. Old paint is common on Burnsville's 1960s and 1970s garages and it adds prep time, not difficulty.
Do you cover Burnsville, or is it too far?
We cover it. Burnsville sits directly west of Apple Valley and Eagan, both of which are already on our list, and it is about an hour from River Falls.
Is a 1970s slab too old to coat?
No. Fifty-year-old concrete is generally sound concrete, it just carries more history: settlement cracks, spalled edges, prior paint, oil. The grind removes the history and we repair what it exposes. What matters is whether the slab is structurally whole, and most Burnsville slabs are.
How long will my commercial space be closed during the install?
Most commercial installs run prep + basecoat + topcoat over a single weekend (Friday night through Sunday). Walk-on Monday morning, full operation Monday or Tuesday. Phased installs (keep half the floor in service while the other half cures, then swap) are available for spaces that genuinely can't close. Larger jobs (5,000+ sq ft) typically need 2-3 days but can be scheduled around your operating hours.
How much does a commercial floor coating cost per square foot?
Standard commercial polyurea installs run $6-8 per square foot for solid-color industrial work and $7-9 per square foot for decorative flake / showroom-grade. Food-service installs with integral cove base + anti-slip aggregate run $8-11 / sq ft. Per-sq-ft cost drops on larger jobs (10,000+ sq ft typically lands at $5-7 / sq ft) because mobilization amortizes.
Do you provide a certificate of insurance?
Yes. $2M general liability coverage, COI provided on request. Standard for commercial work where property managers, GCs, or corporate insurance departments require it. Larger jobs also come with a written scope, milestone schedule, and progress photos.
Is polyurea worth the upgrade vs commercial epoxy?
Yes, in commercial settings the gap is bigger than in residential. Forklift-rated abrasion, hot-tire safety, faster return to service, and lifetime UV stability all matter more in commercial use. Per-sq-ft cost is roughly equivalent to professional commercial epoxy; lifespan is 3-5× longer; and the 24-48 hour return-to-service vs epoxy's 3-7 days saves real money on closed-operation cost.
Can polyurea handle forklift traffic?
Yes. That's actually one of polyurea's strongest applications. The basecoat goes down at higher mil thickness for industrial installs, and polyurea's tensile strength handles point-loads that fracture epoxy. Standard for warehouses, manufacturing floors, and shipping bays.
Will a polyurea floor work in a commercial kitchen or food service?
Yes. We install seamless polyurea with integral cove base for food-service applications. No grout lines or floor-wall seams where bacteria collect. Slip-resistant aggregate standard for wet kitchen environments. Withstands daily wash-down with commercial degreasers and sanitizers. USDA-compatible build.
Can we replace VCT (vinyl composition tile) with polyurea?
Yes, and it's one of the more financially obvious upgrades. VCT requires quarterly stripping + waxing (that recurring labor cost adds up fast). Polyurea is sweep-and-mop, no maintenance. The install pays back within 18-24 months on labor savings for most commercial spaces, and the floor lasts 15+ years vs VCT's 7-10.
Do you handle larger commercial projects (10,000+ sq ft)?
Yes. Larger commercial jobs run as phased installs over multiple days, typically with written milestone schedules and progress photos at each phase. We've installed in warehouses, manufacturing facilities, and large retail. Per-sq-ft cost drops on larger jobs because mobilization amortizes (typically $5-7 / sq ft for 10,000+ sq ft).
What happens if the floor gets damaged during use?
Spot repairs are straightforward: diamond grind the damaged area, re-coat with the same system, blends in cleanly. Most damage from heavy use is impact (dropped equipment, dragged pallets) and is covered for repair under the 15-year warranty under normal use. Abuse, deliberate damage, or improper chemical exposure (battery acid, paint stripper, etc.) is excluded.
Can the floor color match our brand?
Yes. Flake blends are available in dozens of colors and we can match logo or brand colors closely. Solid-color installs allow custom pigment matching. Auto dealers, retail brands, and franchise operators often spec the floor color to match showroom signage or brand standards. Bring the color spec at quote time.

More in Burnsville

All the services we offer in Burnsville, MN.

Whatever the slab (garage, basement, patio, mudroom, commercial) gets the same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty. Bundle pricing if you book multiple rooms in one visit.

Commercial Floor Coatings elsewhere

Commercial Floor Coatings in nearby cities.

Same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty across our entire service area. If you're outside {city}, here's where else we install.

← See Commercial Floor Coatings details and full service area

Get a quote

Ready for a commercial floor coatings install in Burnsville?

Send four photos of your slab and we'll text back a real Burnsville number same-day. No salesperson, no quote-bot, no follow-up calls.

(715) 307-8302 Text Dave · Fastest reply
  • Free on-site measurement
  • Written 15-year warranty
FREE QUOTE

Tell us about your slab.

By submitting you agree to be contacted about your project. We don't sell your info, ever.

Text Dave (fastest) Call