Skip to main content
Altoona, WI · River Falls Metro Mon–Fri 8a–5p · Sat by appt Owner-operated · Veteran-friendly

Surface Prep & Repair · Altoona, WI · Est. 2003

Surface Prep & Repair in Altoona, Wisconsin.

Altoona is a city in Eau Claire County, immediately east of Eau Claire. Home to River Prairie, a fast-growing mixed-use development. About 65 minutes east of River Falls. We install polyurea + polyaspartic floor coatings for Altoona homeowners — diamond-ground prep, custom flake colors, 1–2 day install, written 15-year warranty. Mix of mid-century 1950s-70s housing in the established Altoona core, newer 1990s-2010s suburban builds around Lake Altoona, and post-2015 development in the River Prairie area.

Text Dave · 715-307-8302 See Pricing

Surface Prep & Repair in Altoona

What an install looks like in Altoona.

Altoona is part of the Chippewa Valley install corridor for us. The established Altoona core has 1950s-70s housing with older slabs needing edge prep and occasional crack fill. Lake Altoona and River Prairie developments have newer slabs that install cleanly. We batch Altoona installs with Eau Claire and Chippewa Falls jobs.

Surface Prep & Repair specifically in Altoona

Altoona surface prep is mostly mid-century slab work — settlement cracks, edge spalling, prior paint or 1990s epoxy removal. Newer subdivisions usually only need prep when a previous DIY kit failed. Prep-only is available as a standalone service.

Neighborhoods we work in

  • Downtown / Spooner Avenue
  • Lake Altoona shore
  • River Prairie
  • Otter Creek
  • Highway 53 corridor
  • South Altoona
100% Diamond grind On every coating install
0 Acid etch Ever, on any job
20+ Years experience Surface prep since 2003
Always Included Not an upsell line item

Why we don't install epoxy in Altoona

Why diamond grinding is the only acceptable surface prep — and acid etching is not.

Surface prep is where cheap coating installs get cheap. Acid etching takes 30 minutes with a $40 jug of muriatic acid; diamond grinding takes hours with $30,000 worth of equipment. The cost difference is why some installers acid etch — and the bond difference is why those floors peel. Here's the head-to-head:

Acid Etching What cheap installers do
  • Doesn't open the slab uniformly. Acid reacts with the calcium in concrete unevenly — areas with more cement react more, areas with more aggregate react less. The surface profile after acid is inconsistent.
  • Leaves chemical residue. Muriatic acid leaves chloride ions in the concrete pores. Coatings bonded over chloride residue have a weak chemical bond that fails sooner.
  • Produces a chemical bond, not mechanical. The coating is essentially "glued" to the surface. Mechanical bonds (where the coating fuses into open pores) are dramatically stronger.
  • Doesn't remove existing coatings. Old paint, sealers, or coatings have to come off some other way. Acid won't dissolve them. Many installers acid-etch over partial old coatings — guaranteed failure.
  • Health + environmental concerns. Strong acid in residential garages and basements is unpleasant. The runoff has to go somewhere. Local code is increasingly restrictive on residential acid use.
Diamond Grinding What we use
  • Uniform surface profile. Diamond-tooled grinders cut the same depth across the entire slab regardless of cement-to-aggregate ratio. The surface profile after grinding meets ICRI CSP-3 to CSP-4 standards for coating bond.
  • Removes contamination + weak top layer. Grinding cuts through the laitance (the weak, dust-prone top layer of cured concrete) and any surface contamination — oil, paint, sealers, coatings — in one pass. Clean substrate for the bond.
  • Mechanical bond. The coating fuses into the open concrete pores, locking in. Mechanical bonds resist 4-10× the pull-off force of chemical bonds in published lab tests.
  • Removes any existing coating. Old paint, epoxy, or sealer comes off cleanly. We grind down to bare concrete on every job.
  • HEPA-vacuum dust collection. Industrial grinders with attached HEPA vacuums make zero dust mess in residential interiors. Garage, basement, mudroom — we can grind without making the rest of the house unlivable.

If a coating contractor offers to "save you money on prep" by acid-etching, that's the moment to walk away. The prep is the foundation of the install — saving 30 minutes on prep guarantees a re-install in 18 months. Diamond grinding is the only surface prep we do, and it's included in every coating price.

Altoona Pricing

Surface Prep & Repair cost in Altoona, WI: $7–9 per sq ft.

For a coating install, prep is included in the per-sq-ft coating price — never a separate line item, never an upsell. For standalone prep work (sub-contracting to another coating contractor or repair-only jobs), pricing depends on slab condition + scope.

With Coating Install

Included

any coating job

From $0 to extra
  • Diamond grinding
  • Crack & joint repair
  • Spalling patch as needed
  • Built into coating price
Get my number
Sub-Contract Prep

Standalone

any sq ft

From $2 to $4 / sq ft
  • Diamond grinding only or full prep
  • Coordinate with coating contractor
  • Documented surface profile
  • Larger jobs price lower per sq ft
Get my number
Repair-Only

Bid by scope

linear ft + sq ft

From Quote to by Dave
  • Crack filling (per linear foot)
  • Spall + pit repair (per sq ft)
  • No coating
  • Stopgap before future install
Get my number

Standalone prep is typically a contractor-to-contractor arrangement, but homeowners with damaged slabs sometimes commission repair-only work as a stopgap before a future coating install. Send photos + scope and Dave will quote.

The 6-step install

How we install your floor in Altoona.

Same checklist on every floor. The reason our coatings still look new at year ten when the cheap stuff peeled in year two.

  1. 01

    Assess slab condition

    On-site visit to evaluate slab condition: existing coatings, cracks, spalling, oil contamination, moisture indicators. Determines scope of prep work needed and which grind tooling to use (concrete hardness varies, tooling matches).
  2. 02

    Diamond grinding (full slab)

    Industrial diamond-tooled grinders, HEPA-vacuum dust collection, ICRI CSP-3 to CSP-4 surface profile. Wall-to-wall, edge-to-edge, including corners and tight spots. Removes existing coatings, contamination, and the weak laitance layer.
  3. 03

    Crack & joint repair

    Visible cracks filled with flexible polyurea joint filler that moves with the slab. Control joints either filled flush (smooth surface) or maintained as visible (homeowner preference). Edge cracks at the slab perimeter sealed.
  4. 04

    Spalling + pitting repair

    Spalled surface areas patched with polymer-modified concrete repair compound, troweled flat to match surrounding surface. Pits filled and smoothed. Compound cures overnight, ready for coating the next day.
  5. 05

    Surface clean + final inspection

    Full vacuum sweep + tack-cloth wipe to remove residual dust before coating goes down. Walk-through with homeowner to confirm prep is complete and sign off before basecoat.
  6. 06

    Documented + warrantied

    For standalone prep work, we document surface profile (CSP rating) and crack repair scope so the coating contractor has a record. For our own coating installs, the prep is integrated into the 15-year coating warranty — bond failure due to inadequate prep is on us, not you.

Altoona questions

Common questions for Altoona homeowners.

Do you batch Altoona with Eau Claire jobs?
Yes — they're 5 miles apart. We routinely schedule them in the same week to amortize travel from River Falls.
Are Lake Altoona homes different to install in?
Lakeshore homes pull more humidity through below-grade slabs. We run a calcium chloride MVER on every below-grade install near the lake.
How long is the lead time?
Typically 2-3 weeks out from quote because we batch Chippewa Valley jobs into single trips.
Why does my floor coating keep peeling?
Almost always inadequate surface prep. The most common cause is acid etching instead of diamond grinding — the chemical bond is dramatically weaker and fails first under thermal cycling, moisture, or load. Other causes: coating applied over old coating without grinding it off, moisture transmission from below (untested), or hot-tire pickup damage on epoxy. If a previous floor coating peeled within a few years, the next one needs to be installed differently — start with full diamond grinding to remove whatever's left, then a polyurea (not epoxy) system on top.
What's the difference between diamond grinding and acid etching?
Diamond grinding mechanically cuts the concrete surface with diamond-tooled abrasives, opening the pores uniformly and creating a mechanical bond profile (ICRI CSP-3 to CSP-4). Acid etching uses muriatic acid to chemically react with the surface — uneven, leaves chloride residue in the pores, creates a weaker chemical bond. Lab pull-off tests show diamond-ground surfaces hold coatings at 4-10× the bond strength of acid-etched surfaces. We never acid etch.
Is surface prep included in the coating price?
Yes — diamond grinding, crack repair, and spalling patch are included in every coating install we do. It's not a separate line item or upsell. The 15-year warranty exists because the prep underneath it is right; charging extra for prep would be charging extra for the foundation of the install.
Do you do standalone surface prep without a coating?
Yes — for two cases: (1) sub-contracting to another coating contractor whose own crew doesn't have grinder equipment, and (2) repair-only work for homeowners with cracks or spalling that need fixing but who aren't ready for a full coating yet. Standalone prep runs $2-4 per square foot depending on slab condition and scope; repair-only is bid by scope.
How long does the diamond grinding take?
For a typical 2-car garage (~440 sq ft), grinding runs 2-3 hours including setup, wall-to-wall coverage, and cleanup. Larger spaces scale linearly. Crack repair adds 30-60 minutes depending on linear footage. Spalling repair adds 1-2 hours per 100 sq ft of repair area. The dust is contained by HEPA vacuum so the rest of your house stays livable during grinding.
Will the dust from grinding be a problem?
No — our grinders run with attached HEPA-vacuum dust collection. Effectively zero airborne dust escapes during grinding. We can grind in residential garages, basements, and mudrooms without affecting other parts of the house. After grinding we vacuum the slab a final time before any coating goes down.
What if my slab has cracks — can it still be coated?
Almost always yes. Cracks get filled with flexible polyurea joint filler before the coating goes down. The filler bonds to both sides of the crack and stretches with future movement, so the crack doesn't telegraph back through the coating. Exceptions: structural cracks (deep, through-slab, or growing) are signs of a foundation issue that should be addressed before coating. We'll tell you on-site.
What about old paint or sealer on the floor?
Diamond grinding removes most old paint, sealers, and coatings cleanly in one pass. Stubborn cases (heavy enamel paint, deeply penetrating sealers) get an extra grind pass or a chemical degrease step before grinding. By the time the new coating goes down, the slab is bare concrete substrate.
Do you handle severely spalled or damaged concrete?
Most spalling, pitting, and minor surface damage is repairable with polymer-modified concrete compound, troweled flat, and overcoated. Severely damaged concrete (large sections lifted from frost heave, structural cracks, deep through-slab damage) is sometimes beyond restoration — a coating over a structurally bad slab buys 1-2 years before the underlying problem reappears. We'll tell you straight if your slab needs replacement instead of restoration.
Why do you test for moisture before coating below-grade?
Below-grade slabs (basements, walk-outs, lower-level garages) transmit ground moisture upward through the concrete. High moisture causes coating delamination — the bond between coating and slab fails as moisture vapor builds up underneath. We run an MVER test before coating any below-grade surface; readings tell us whether the slab is dry enough for a standard install or needs a moisture-mitigation primer underneath. Avoids the most common cause of below-grade coating failure.

More in Altoona

All the floor coatings we install in Altoona, WI.

Whatever the slab — garage, basement, patio, mudroom, commercial — same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty. Bundle pricing if you book multiple rooms in one visit.

Surface Prep & Repair elsewhere

Surface Prep & Repair in nearby cities.

Same diamond-ground prep, same polyurea + polyaspartic system, same 15-year warranty across our entire service area. If you're outside Altoona, here's where else we install.

← See Surface Prep & Repair details and full service area

Talk to Dave

Ready for a surface prep & repair install in Altoona?

Send Dave four photos of your slab — he'll text back a real Altoona number same-day. No salesperson, no quote-bot, no follow-up calls.

715-307-8302 Text Dave · Fastest reply
  • Free on-site measurement in Altoona
  • Written 15-year warranty
  • No subcontractors, no upsells
ALTOONA QUOTE

Tell Dave about your Altoona slab.

By submitting you agree to be contacted about your project. We don't sell your info, ever.

Text Dave (fastest) Call
This site uses cookies for analytics + ads attribution. Privacy · Cookies